Alignment: Difference between revisions

From Mu2eWiki
Jump to navigation Jump to search
No edit summary
 
(3 intermediate revisions by the same user not shown)
Line 1: Line 1:
==Definitions==
Alignment describes the corrections to the geometric descriptions of actual detector pieces compared to their nominal as-engineered description.  An example
is ''rigid body alignment'', which describes the detector piece's position and orientation within some larger frame, ignoring any internal distortions to the
piece.  Alignment is often built up out of a nested set of corrections, moving outwards to larger frames.


 
The specifics of the tracker alignment are described on the page [[TrackerAlignment]].
==Technical Definition==
This section explains how the tracker alignment is defined. 
 
* There are three places that alignment transforms are inserted
** between the whole tracker and the nominal geometry
** between each plane and the aligned tracker
** between each panel and the aligned plane
* transforms
** apply rotation before displacement
** a rotation is defined as right-handed about the local x, then y, then z axes (rad)
** add an offset in position (mm)
* tracker geometry object are in coordinate centered at the nominal tracker center
 
Here is how the geometry is conceptually built up, including the alignment
 
<ol>
<li> Straws are placed within the panel
* this uses the local panel coordinate system, defined as UVW, a right-handed coordinate system.  These correspond to the XYZ coordinates of the Duke panel X-ray mapper, defined in Mu2e document 5703.
* The straw direction points along the +U axis, which points from the High Voltage (HV) side of the DRAC electronics board to the Calibration (cal) side.
* straw 0 is the longest, innermost straw, straw 95 is the shortest, outermost straw.
* V points radially outwards, from the center of straw 0 to the center of straw 94.
* W is perpendicular to the panel, and to U and V, pointing from the back of the base plate to the cover. This is roughly from the center of straw 1 to the center of straw 0
* panel U=0 is defined by the nominal symmetry axis of the panel
* pane V=0 is defined to be midway between innermost and outermost straw centers, between straws 47 and 48.
* panel W=0 is defined to be midway between the straw layers, which is also midway between the innermost and outermost straw centers
</li>
<li>Apply the straw alignment.  These are defined in terms of displacements in V and W at either end (HV and Calibration) of the straw, where the straw intersects the manifold (radius=700 mm).  The mylar envelope and wire have separate corrections.
<li>Apply the panel alignment of rotations and displacements.  These are rigid body rotation and translations WRT the local panel UVW coordinate system.
<li>Place the panel in the nominal plane.  This involves rotating the nominal panel center to its nominal phi position around the z axis, and adding its nominal displacement in Z and radially outwards.  By convention, the nominal plane is defined as plane 0, described in Mu2e document 888.  The nominal plane coordinate system (XYZ) is centered on the plane, with directions as defined by the Mu2e detector coordinate system.
<li>Apply the plane alignment of rotations and displacements, with respect to the nominal plane coordinate system.
<li>Place the plane within the nominal tracker.  This involves moving it along the z axis, and rotating half the planes around the Y axis by 180 degrees.  The pattern of plane rotations is defined in Mu2e document 888.  It amounts to building a station by rotating one plane around Y by 180 degrees, then rotating every-other station around Y by 180 degrees.
<li>Place the tracker within the Mu2e detector coordinate system by applying the tracker alignment.  The detector coordinate system is defined as the nominal (perfect) tracker coordinate system.
</ol>
 


[[Category:Computing]]
[[Category:Computing]]
[[Category:Code]]
[[Category:Code]]
[[Category:Database]]
[[Category:Database]]

Latest revision as of 22:38, 13 January 2021

Definitions

Alignment describes the corrections to the geometric descriptions of actual detector pieces compared to their nominal as-engineered description. An example is rigid body alignment, which describes the detector piece's position and orientation within some larger frame, ignoring any internal distortions to the piece. Alignment is often built up out of a nested set of corrections, moving outwards to larger frames.

The specifics of the tracker alignment are described on the page TrackerAlignment.

Retrieved from "http://mu2ewiki.fnal.gov/w/index.php?title=Alignment&oldid=17733"