SubmitJobs

Introduction

This page is part of the standard simulation workflow. It uses the jobsub package through the mu2eprodsys script in mu2egrid. Before this step, you should have prepared a set of fcl files for the job, and have them in a set of files, called fcllist.00, etc., in the example. Each of these files will drive one submission, or cluster. You should also have defined the Offline version (the filespec of the setup.sh file) to use in the project. This should be the same as the Offline you set up during fcl generation.

Setup

It is advisable to start with a clean shell (no Offline setup), because the jobsub_client package requires a different Python version then Mu2e Offline.

setup mu2e
setup mu2egrid
setup mu2efiletools

Job submission

The mu2eprodsys command is used to submit grid jobs. A single execution of mu2eprodsys submits a single Condor cluster of jobs. We have been asked to limit the size of clusters to 10,000 jobs. If the total number of jobs to be run exceeds 10,000, the list of fcl files should be split into several smaller files with each each file not exceeding 10,000 lines. One can use the Linux split -l command to do this.

The required parameters are:

• --setup the setup script that determines which version of Offline to use. To run jobs offsite, the Offline release must reside in cvmfs. For on-site running one can put code on the /mu2e/app disk.
• --fcllist The list of uploaded fcl files in /pnfs
• --dsconf An user-defined string that will be used for the "configuration" field of output files.

Some of the options

• --dsowner the "owner" (in the dataset naming convention sense) of output datasets. Defaults to the user who runs mu2eprodsys, unless the user is "mu2epro". In the latter case --dsowner is set to "mu2e" to produce "official" datasets.
• --wfproject can be used to group results in the outstage area. The use of this option is highly recommended. For example, --wfproject=beam or --wfproject=cosmic.
• --expected-lifetime should be used to set an upper limit on the wallclock job duration. The value is passed directly to jobsub_submit, see its documentation for more information.

Run mu2eprodsys --help to see all the options.

If you plan to register the fcl files in SAM, you can submit the fcl file list before there are registered.

Outstage location

By default the outputs will be placed into

/pnfs/mu2e/scratch/users/$USER/workflow/$WFPROJECT/outstage/

where $USER is the submitter user name, and $WFPROJECT is specified by the --wfproject parameter (the default is "default"). If --role=Production (see authentication) is used (default for the mu2epro user), the outputs will go into

/pnfs/mu2e/persistent/users/$USER/workflow/$WFPROJECT/outstage/

instead.

Each submission, or call to mu2eprosys creates one cluster of jobs. The number of jobs in the cluster is determined by how long the list is in the fcl list files. The script will print out a jobId like

Use job id 18497021.0@fifebatch2.fnal.gov to retrieve output

It is a good idea to save this so you can track this cluster.

Each submission will create a new directory in the outstage area, like /pnfs/mu2e/scratch/users/$USER/workflow/$WFPROJECT/outstage/15503895.beam_p03_17_03_31_16_32_48_1490995968_0 in each directory will be subdirectories like 00 which serve to reduce the number of files in each directory, then in those directories are directories for each job, like 0000, and the job output is here.

Example

  mu2eprodsys --setup=/cvmfs/mu2e.opensciencegrid.org/Offline/v5_6_7/SLF6/prof/Offline/setup.sh \
  --wfpro=pion-test \
  --fcllist=fcllist.00 \
  --dsconf=v567 \
  --expected-lifetime=5h

Monitoring

You can use the mu2e_clusters script from the mu2egrid package, or the jobsub_q command, to check the status of your jobs.

If you see that some jobs are on hold (the "H" state), look for HoldReason in the output of jobsub_q --long --jobid <jobid>. If you see a PERIODIC_HOLD message, that means the job tried to use more resources (memory/disk/time) than you asked for. jobsub_rm the offending jobs and re-submit after adjusting the requirements. If HoldReason is not a PERIODIC_HOLD, open a servicedesk ticket.

See the operation links page for links to useful monitors, in particular mu2e grafana. If the jobs go on hold, the jobs list will tell you which resource limits you violated.

Checking output

The mu2eClusterCheckAndMove script from the mu2efiletools package can be used to separate "good" and "failed" jobs. One does not have to wait until all jobs complete; mu2eClusterCheckAndMove can be run periodically on job outputs in the outstage area.

cd .../workflow/$WFPROJECT/outstage
mu2eClusterCheckAndMove 15503895.beam_p03_17_03_31_16_32_48_1490995968_0 >& \
    $WORKDIR/cam_`date +"%y_%m_%d_%H_%M_%S_%s"`.log &

After running the mu2eClusterCheckAndMove script, in the output area are there will be three directories:

.../workflow/$WFPROJECT/outstage
.../workflow/$WFPROJECT/good
.../workflow/$WFPROJECT/failed

As they are checked, job directories are moved from "outstage" into "good" and "failed" subdirectories, as needed. The script prints a summary of the results.

Two frequently used options:

• --timecut The script will not look at job outputs that are "too fresh" and may still be written out. The default minimal age is 7200 seconds. If you know that all jobs in the cluster have finished, you can set --timecut to a small value instead of waiting for 2 hours before checking the results.
• --nosam By default the script talks to SAM to ensure that there are no duplicate jobs. Because of glitches in grid running, sometimes one gets more than one copy of files for the same jobs. However if the original fcl files have not been registered with SAM, the uniquiness check can not be performed. This obviously means if you are registering the fcl files in SAM, you don't want to run this script before that registration is done.

Recovering jobs

If the fcl dataset was registered in SAM, then you can use the following method to make a list of jobs to recover. After all jobs from the current submission have completed and processed with the mu2eClusterCheckAndMove script, so that outstage area is empty, SAM has a record of all "good" jobs from that attempt. Continuing with the pion example, one can run

mu2eMissingJobs --fclds=cnf.gandr.my-test-s1.v0.fcl  --dsconf=v567  > failed-jobs.txt

then use the list of failed jobs to re-submit them with mu2eprodsys. It is important to consistently use the same --dsconf (and --dsowner, if non-default) throughout the process.

If the fcl dataset was not registered in SAM, then you need to make a list of job directories in the good directory, find missing entries, and construct a new fcl file list from that.

Return to workflow

At the end of this procedure, you should have a complete set of output files in the good subdirectory of the output area.

• production simulation workflow