RunNumbers

Introduction

On this page we reserve run number ranges to attempt to prevent multiple uses for a single run number. This is important to not generate conflicting file names or conditions database entries, and to improve communication and documentation.

The plan to assign run number ranges, in this period before beam data, was discussed and agreed in the Trigger Group meeting. Any group requesting a run number range must stay within that range until they request another block of run numbers. An OTS TDAQ instance can have its initial run number set to the beginning of the range, then it can increment the run number automatically with each run start. The Trigger Group will continue to discuss and develop a plan to coordinate run numbers in a central, database-backed method.

Only the Calibration Coordinator or Offline Co-leaders are allowed to reserve run ranges.

• use the next available numbers above the reserved
• be modest in the number reserved (you can always come back for more)
• tests and simulation will have run number below 100,000
• data, including test beam, test stands and cosmics, will have run numbers above 100,000

Reserved run numbers

The "Organizer" of a run number range has the primary responsibility to assure the group using the run numbers stays within the run range, or arrange for another block of numbers.

Start	End		Name	Organizer	Notes
1	99		userSpace	Rob Kutschke	arbitrary user needs (not production)
100	999		offline	Rob Kutschke	scratch or temporary experiments
1000	1099		legacy	Rob Kutschke	numbers commonly used in simulation before this system
1100	1199		database tests	Ray Culbertson	run dependence tests
1200	1299		MDC2020	Dave Brown (LBL)	MDC2020 production simulation with run dependence
1205	1205		MDC2020 extracted	Dave Brown (LBL)	MDC2020 production simulation of extracted position
1300	1399		RDM	Ray Culbertson	test data for file movement and processing
1400	...		...	....	next non-data reservations
100000	100999		tracker VST	Richie Bonventre	tracker VST 2020-2021
101000	101999		STM test beam	Andy Edmonds	Dresden test beam 4/2022
102000	102999		module-0	Eleonora Diociaiuti	Calorimeter module-0
103000	103999		CRV	Ralf Ehrlich / Simon Corrodi	CRV data from the Wideband teststand
104000	104999		...	....	next data reservations
105000	999999		automatic	Antonio Gioiosa	automatic online database

Simulation run numbers

Simulation will eventually need run dependence. A good example would be if a tracker plane is turned off or recovered during the run, then we will want to run a job which simulated the difference tracker configuration in the proper proportions. The plan is that when a simulation campaign starts, there will be the following steps

1. the collaboration (Offline, Operations, Physics groups) will define periods of stable running called "simulation periods", recorded as run number ranges. We expect this will be on the order of 10's of periods per year. (We also expect "run periods" defined by production and analysis operational needs, and may or may not be similar to the simulation periods).
2. for each simulation period, a representative set of conditions (typically database calibration tables) will be selected from, or derived from, the calibration data of the data runs in the period. More conditions data, appropriate only for simulation can be added.
3. a sequential set of runs, from the non-data run ranges, will be reserved for this simulation campaign. The size of the set will essentially be equal to the number of simulation periods.
4. The calibration manager will create a new purpose and version in the conditions database for this simulation campaign
5. The conditions data prepared for each simulation period will be associated to a run in the reserved run range though the standard conditions database techniques. The data in these runs will be collected under the new purpose/version.
6. simulation jobs will produce data in the reserved run ranges, with each run produced in proportion to the data taken during the corresponding simulation period, and conditions data taken from the new purpose/version.
7. reconstruction jobs running on this simulation should be able to use the described conditions data.

This section is an outline. Additional detailed techniques will need to be defined for staging, mix-in options, and systematic variations of conditions.

Some History

talk
talk
talk
Ray talk page 3
Richie talk page 7

Approximate survey of existing run numbers. 1000 is current example for sim.

    count runnumber
    19 1
      1 2
      1 3
      5 4
      1 5
      1 7
     23 1000
     10 1001
    234 1002
      6 1052
      3 1053
      1 1357
      6 1500
     11 1600
      5 1700
     10 1800
      1 2000
      1 2001
      9 2700
     20 2701
      2 2705
     57 4001
      1 4002
      3 5001
      1 9002
      1 645440
      1 1792836
      2 2102784
      1 3344213
    115 11911024-19236224